January 09, 2013

The Physics Of Archery




There is a very interesting physical phenomenon in the physics of archery, known as Archer's paradox. When an arrow is released to the left (or right) of a bow and is deliberately aimed off target, it will straighten out during release and hit the target. This paradoxical situation is known as Archer's paradox. The figure below illustrates this.

Bows like the longbow shown in the first picture, must have the arrow placed to the right or left of the bow shaft. As a result, the arrow is not aligned with the median plane of the bow. So in order for the arrow to fly straight, and re-align with the median plane of the bow during release, it must "undulate" around the bow shaft. The two videos below show the motion of the arrow just after release using a high-speed camera. It only takes milliseconds for the arrow to fly past the bow.

Due to the relatively high force of the bow string acting on the arrow, it rapidly accelerates and a high-speed camera is required to capture the motion. Also, because this large force is acting in the direction of the arrow shaft, it begins to oscillate (fishtail) back and forth. This is the natural vibration the arrow experiences when subjected to a brief but large force. It's similar to hitting something with a hammer and it vibrating as a result. The force acting on the arrow is equal to the draw force as the archer pulls the string back to the release position. This force can be in the range of 30-50 lb which is very large compared to the mass of the arrow, which is why it accelerates so rapidly (due to Newton's second law, F = ma).


Thus, the physics of archery is more than just shooting an arrow at the target. One must also account for the oscillation of the arrow during the release. In the explanation that follows, more details will be given on what occurs when the arrow is released and why it straightens out.

The figure below shows the initial set up, as the archer pulls the string back and is ready to release it.



In the above figure the center shot line (line of sight) is kept deliberately to the right of the center of the target by a distance ε. This is because the arrow will straighten out and fly parallel to the median plane, but will also be offset from it by a distance ε. This offset distance is known by the archer, only from experience.

The figure below shows the arrow immediately after release.







In this first stage illustrated above, three things happen:

1. As the archer opens his fingers the string slides off and moves to the left. This happens because, as the fingers open the friction between string and finger becomes insufficient to hold the string in place. So it slides off, and it does so at an angle to the median plane of the bow. This results in an initial sideways movement of the string. In reality, it would be impossible for an archer to open his fingers fast enough to prevent the string from sliding off to the side a bit, since the string moves much too quickly. However, for purposes of getting the arrow to fly straight it is desirable that the string initially deflects to the left a bit. It is the first stage of what must happen during the mechanics of the release.

2. The leftward motion of the string excites a mode of oscillation where the arrow begins to vibrate in the plane of the page. The string force F1contributes to the deflection of the arrow δ beyond that due to the leftward motion of the string by itself. Note that F1 acts in the direction of the arrow shaft.


3. The arrow is contacting the bow at point P due to a clockwise moment, which can be taken about the center of mass G (of the arrow) at the instant shown. This moment is equal to F1r1, where r1 is the moment arm F1 makes with G.

The figure below shows the arrow as it reaches the approximate halfway point past the bow.








During this second stage illustrated above, two things happen:


1. The string moves to the right, as it restores its original position with the median plane of the bow. As a result, the string "pulls" on the arrow with a force F2.


2. The tip of the arrow T moves slightly to the left. This is due to a counter-clockwise moment taken about the center of mass G at the instant shown. This moment is equal to (F1r1 + F2r2), where r2 is the moment arm F2 makes with G.


The reason the tip of the arrow T moves to the left is obvious if one considers the general moment equation for a rigid body.





Where:


ΣMG is the sum of the moments about the center of mass G


IG is the moment of inertia of the arrow about the center of mass G, about an axis pointing out of the page


α is the angular acceleration of the arrow


Since the sum of the moments is counter-clockwise, α is also counter-clockwise, which means the arrow rotates counter-clockwise.


Now, the lateral (left and right) motion of T is due to two separate contributions:


(a) The counter-clockwise rotation of the arrow due to α. This causes T to move to the left.


(b) The lateral (translational) motion of the arrow due to the string pulling E to the right. Since E is below the sweet spot (shown in the figure above), movement of E to the right causes movement of T to the left. (The sweet spot is discussed in detail in The Physics Of Hitting A baseball).


Since both contributions from (a) and (b) cause T to move to the left, the resultant motion of T is to the left.


It is likely that contribution (a) is much greater than contribution (b), but for purposes of making the analysis more complete one must consider the latter contribution as well.


Note that, technically speaking, the arrow is not rigid because it's oscillating, but at the instant shown you can treat it as a rigid body.


The motion of T to the left essentially straightens out the path of the arrow from the first stage so that it flies straight upon leaving the bow.

In the third and final stage illustrated below, the arrow exits the bow completely, having completed (approximately) one full oscillation. The arrow is now flying straight to the target. It will continue oscillating all the way to the target, with oscillation gradually decreasing in amplitude, but maintaining the same frequency throughout the flight.





A subtle point is that, due to the induced counter-clockwise angular acceleration α of the arrow in the second stage, one might expect the arrow to keep turning counter-clockwise during the flight. However, this is not the case. The vanes (fletchings) at the back of the arrow straighten out the arrow during flight, helping it fly true to the target. So any rotation is quickly eliminated.

In the figures above, the bow is held with the left hand and the string is released with a right-handed draw (Mediterranean release), with the arrow placed on the left of the bow. If one were to use a left-handed draw the arrow would need to be placed on the right of the bow, to create the equivalent arrow mechanics during release. So in this case the left-handed draw is a "mirror" of the right-handed draw. So the physics of archery taking place during the release is mirrored, as well.

If one were to release the string using the thumb of the right hand (Mongolian release) the arrow would still need to be placed to the right of the bow since the string initially deflects to the right. But there is no hard and fast rule, since some archers use a variety of different techniques to obtain a straight shot.

Historical evidence of ancient arrows and bows shows that primitive archers were able to compensate (at least somewhat) for arrow oscillation during release. This is impressive considering they were not nearly as well versed in the physics of archery, as we are today.

It is important that the time it takes for the arrow to oscillate through one full cycle is approximately the time it takes for the arrow to exit the bow. If the oscillation time is too slow the back of the arrow may "slap" the bow shaft when it flies past, causing it to deflect off course and veer too far to the right. If the oscillation time is too fast, the arrow flight path may not straighten out sufficiently and it will veer to the left of the target.

The stiffness of the arrow (resistance to bending) is commonly referred to as the "spine". The stiffer the spine, the more rigid the arrow and the higher the frequency of oscillation. So the stiffness of the arrow must be just right to match the draw force of the bow, the draw length, and the archer's shooting technique. All these play an important role in determining the right choice of spine for the arrow.

It is possible to analytically predict the frequency and amplitude of oscillation of the arrow during release and model that, but it is too complicated to discuss here and won't significantly add to the basic understanding put forth here. However, great inroads have already been made in this regard, with analytical models achieving a fair degree of accuracy.

But in general, it's best to rely on the combination of analytical and empirical data already out there when determining the correct arrow to use for your bow and particular release style. And unavoidably, calibrating for the physics of archery (e.g. Archer's paradox), means one must experiment anyway to see what works best.

4 comments:

  1. Thanks for finally talking about >"The Physics Of Archery" <Loved it!

    ReplyDelete
  2. What's up to every , since I am actually eager of reading this
    web site's post to be updated regularly. It includes good information.

    ReplyDelete
  3. I am really inspired along with your writing abilities as smartly as with the layout to your weblog.
    Is that this a paid subject matter or did you customize it your self?

    Either way stay up the nice high quality writing, it's
    rare to see a great weblog like this one nowadays..

    ReplyDelete
  4. It's a pity you don't have a donate button! I'd definitely donate to this brilliant blog!
    I suppose for now i'll settle for book-marking and adding your RSS feed to my Google account.
    I look forward to brand new updates and will talk about
    this blog with my Facebook group. Chat soon!

    ReplyDelete